2025-07-29-M5StickC_RF_2in1

M5StickC_RF_2in1

注意：所有模块需要Bruce固件中使用，链接：[https://github.com/pr3y/Bruce/]

How to use 使用方法

CC1101

  • To use the CC1101 in Bruce, turn off your M5 device，set the switch to CC1101 and connect the module .
    将M5设备关机，模块开关拨到CC1101，插入到M5设备。
  • Turn on the device, then navigate to "RF->Config->RF Module" and select "CC1101 on SPI" pics here. 打开设备，然后导航到“RF->Config->RF Module”并选择“CC1101 on SPI”此处为图片。
  • If the "CC1101 not found" error message appears, turn off the M5 device, recheck the switch and try again.
    如果出现“CC1101未找到”错误消息，请关闭M5设备，重新检查模块开关位置，然后重试。
  • If no error is shown, then the CC1101 is initted correctly, and you can use it in the RF menu.
    如果没有显示错误，则CC1101已正确初始化，您可以在RF菜单中使用它。
  • For this module you can also set a custom frequency in the supported subranges: 300-348 MHZ, 387-464 MHZ and 779-928 MHZ. Setting an empty or invalid frequency will reset to the default 433.92 MHZ. This setting will only affect the receive and jamming features. Transmitting from a sub file will always use the frequency specified inside the file regardless of the user setting.
    对于此模块，您还可以在支持的子范围内设置自定义频率：300-348 MHZ、387-464 MHZ和779-928 MHZ。设置空频率或无效频率将重置为默认的433.92 MHZ。此设置只会影响接收和干扰功能。从sub文件传输时，无论用户设置如何，都将始终使用文件中指定的频率。

NRF24

  • To use the NRF24 in Bruce, turn off your M5 device, set the switch to NRF24 and connect the module.
    将M5设备关机，模块开关拨到NRF24，插入到M5设备。
  • Turn on the device, then navigate to "NRF" . 打开设备，然后导航到“NRF”来使用。
  • If the "NRF not found" error message appears, turn off the M5 device, recheck the switch and try again.
    如果出现“NRF未找到”错误消息，请关闭M5设备，重新检查模块开关位置，然后重试。
  • If no error is shown, then the NRF24 is initted correctly, and you can use it in the NRF menu.
    如果没有显示错误，则NRF24已正确初始化，您可以在NRF菜单中使用它。

特别声明 / Special Declaration

  1. 本模块仅为射频模组与主机之间的物理连接模块。
    This module serves solely as a physical connection interface between the RF module and the M5stack devices.

  2. 本模块不包含任何软件、驱动程序或固件。
    This module does not contain any software, drivers, or firmware.

  3. 本模块不具备任何干扰、拦截或阻止授权无线电通信的功能。
    This module does not possess any functions to interfere with, intercept, or block authorized radio communications.

  4. 请用户务必在当地法律法规允许的范围内使用本设备。用户需对其最终用途及操作的合法性承担全部责任。
    Users must use this device strictly within the scope permitted by local laws and regulations. The user assumes full responsibility for the legality of its end-use and operation.

Acknowledgments

For more details and information, see Bruce Firmware Wiki.