2026-01-22-Cardputer ADV_RF_2in1 2.0 Module

Cardputer ADV_RF_2in1 2.0

注意：所有模块需要Bruce固件中使用，链接：[https://github.com/pr3y/Bruce/]

Image.jpeg Image-1.jpeg

How to use 使用方法

Setup

  • After flashing the Bruce firmware, edit the pin configuration file “BrucePins.conf” located in the root directory of the SD card (or internal storage). 刷好Bruce固件之后，编辑SD卡（或者内置存储）根目录下的引脚配置文件 BrucePins.conf config1.jpeg

  • Find the CC1101_Pins, change the CS pin to 13, and change the IO0 pin to 5. 找到CC1101_Pins，将cs引脚改为13，io0引脚改为5。 2026-01-22_16h05_36.png

  • Find NRF24_Pins, and similarly change the CS pin to 6 and the IO0 pin to 4. 找到NRF24_Pins，同样将cs引脚改为6，io0引脚改为4。 2026-01-22_16h06_18.png

  • Install the antenna, round-tip antenna for NRF24/2.4G, stubby chili antenna for CC1101/433M.
    先安装天线,圆头天线安装至NRF24/2.4G，小辣椒天线安装至CC1101/433M。 Image-5.jpeg

  • Then insert the module into the Cardputer ADV's IO slot. 将模块插入Cardputer ADV的IO插槽内。 Image-6.jpeg

CC1101

  • To use the CC1101 in Bruce, turn off your Cardputer and connect the module .
    将Cardputer ADV关机，模块插入Cardputer ADV。
  • Turn on the device, then navigate to "RF->Config->RF Module" and select "CC1101 on SPI" pics here. 打开设备，然后导航到“RF->Config->RF Module”并选择“CC1101 on SPI”此处为图片。
  • If the "CC1101 not found" error message appears, turn off the Cardputer ADV, recheck the connection and try again.
    如果出现“CC1101未找到”错误消息，请关闭Cardputer ADV，重新检查模块插入情况，然后重试。
  • If no error is shown, then the CC1101 is initted correctly, and you can use it in the RF menu.
    如果没有显示错误，则CC1101已正确初始化，您可以在RF菜单中使用它。
  • For this module you can also set a custom frequency in the supported subranges: 300-348 MHZ, 387-464 MHZ and 779-928 MHZ. Setting an empty or invalid frequency will reset to the default 433.92 MHZ. Transmitting from a sub file will always use the frequency specified inside the file regardless of the user setting.
    对于此模块，您还可以在支持的子范围内设置自定义频率：300-348 MHZ、387-464 MHZ和779-928 MHZ。设置空频率或无效频率将重置为默认的433.92 MHZ。从sub文件传输时，无论用户设置如何，都将始终使用文件中指定的频率。

NRF24

  • To use the NRF24 in Bruce, turn off your Cardputer ADV and connect the module.
    将Cardputer关机，模块插入到Cardputer ADV。
  • Turn on the device, then navigate to "NRF" . 打开设备，然后导航到“NRF”来使用。
  • If the "NRF not found" error message appears, turn off the Cardputer ADV, recheck the connection and try again.
    如果出现“NRF未找到”错误消息，请关闭Cardputer ADV，重新检查模块插入情况，然后重试。
  • If no error is shown, then the NRF24 is initted correctly, and you can use it in the NRF menu.
    如果没有显示错误，则NRF24已正确初始化，您可以在NRF菜单中使用它。

特别声明 / Special Declaration

  1. 本模块仅为射频模组与主机之间的物理连接模块。
    This module serves solely as a physical connection interface between the RF module and the M5stack devices.

  2. 本模块不包含任何软件、驱动程序或固件。
    This module does not contain any software, drivers, or firmware.

  3. 本模块不具备任何干扰、拦截或阻止授权无线电通信的功能。
    This module does not possess any functions to interfere with, intercept, or block authorized radio communications.

  4. 请用户务必在当地法律法规允许的范围内使用本设备。用户需对其最终用途及操作的合法性承担全部责任。
    Users must use this device strictly within the scope permitted by local laws and regulations. The user assumes full responsibility for the legality of its end-use and operation.

Acknowledgments

For more details and information, see Bruce Firmware Wiki.